Products
-
FRP Liquid Alkali Storage Tank
-
Square Counterflow Cooling Tower
-
FRP Mixing Tank
-
Cooling Tower
-
Potassium Sulfate EPC Project
-
FRP Cooling Tower
-
Scrubbing tower
-
FRP anode tubes
-
Closed Circuit Cooling Towers
-
PPH Agitator tank
-
Wet electrostatic precipitator
-
FRP Wastewater Storage Tank
-
PPH tower
-
Vertical FRP Tank
-
FRP water tanks
-
Air cooled heat exchanger
Evaporative condenser
Based on the working principle of thermodynamic heat transfer, the evaporative condenser makes the high-temperature gaseous refrigerant in the coil exchange heat with the spray water and air outside the coil. The super wind force of the induced draft fan makes the spray water completely cover the surface of the coil, and the heat exchange effect is significantly increased by the wind force of the water. After absorbing heat spray water and air temperature, some water from liquid to gas, the latent heat of evaporation take away a lot of heat, heat the water in the air is dehydrator intercept and collected the water in the heat transfer in heat transfer layer by air cooling, temperature lowering into the sump tank, by circulating water pump to spray again continue to cycle in the system. The water evaporating into the air is automatically replenished by the control of the floating ball valve .
Description
marker
Based on the working principle of thermodynamic heat transfer, the evaporative condenser makes the high-temperature gaseous refrigerant in the coil exchange heat with the spray water and air outside the coil. The super wind force of the induced draft fan makes the spray water completely cover the surface of the coil, and the heat exchange effect is significantly increased by the wind force of the water.
After absorbing heat spray water and air temperature, some water from liquid to gas, the latent heat of evaporation take away a lot of heat, heat the water in the air is dehydrator intercept and collected the water in the heat transfer in heat transfer layer by air cooling, temperature lowering into the sump tank, by circulating water pump to spray again continue to cycle in the system. The water evaporating into the air is automatically replenished by the control of the floating ball valve .
Evaporative condenser is the use of the latent heat of water is the water at room temperature of evaporation absorbs heat to achieve the purpose of cooling, the same quality of heat absorbed by water evaporation is 5 degrees warmer water heat 116 times, when to take the same heat so evaporative condenser water consumption is much lower than traditional water cooled condenser,which is evaporative cooling is the root cause of the electricity saving water.
In the food, dairy products, cold storage, beer,chemical,petrochemical,pharmaceutical,refrigeration section are widely used in coal mine industry, etc.
contact us
Related popular products
Vertical FRP Tank
Glass fiber reinforced plastic storage tank is one kind of glass fiber reinforced plastic products. It is a new type of composite materialmade by winding glass fiber and resin as binder through microcomputercontrolledmachine.
Closed Circuit Cooling Towers
The DGCC Series Tube-and-Header Type Closed Circuit Cooling Towers employ advanced latent heat transfer technology, delivering significantly higher heat exchange efficiency compared to traditional sensible heat transfer methods.Featuring a PVC-free heat exchange layer with an all-coil structure, the tower eliminates common issues associated with conventional open towers, such as packing clogging and aging.
FRP Reactor
The fiberglass reaction vessel has good anti-corrosion and temperature resistance, making it a high-performance and easy-to-use reaction vessel.
FRP chimneys
The fiberglass chimney is processed by winding with FRP(Fiberglass Reinforced Plastic)raw materials.The product has the characteristics of low cost,short production cycle,long service life,light weight,high strength,high rigidity,simple installation,smooth inner and outer surfaces,good anti-aging performance,and excellent corrosion resistance.Moreover,sprayers,filters,etc.can be conveniently added to absorb the harmful components in the flue gas.
FRP Desulfurization Tower
The internal structure design is reasonable, such as the use of efficient spray devices, fillers, etc., which can fully contact the flue gas with the desulfurizer, undergo chemical reactions, and effectively remove sulfur dioxide and other sulfides in the flue gas. The desulfurization efficiency can usually reach over 90%, or even higher, and can meet strict environmental emission standards.
Cooling Tower
The surface of fiberglass cooling towers is smooth and can be made in various colors and shapes, which can coordinate with the surrounding environment and have good decorative properties, especially suitable for places that require environmental aesthetics.
FRP Scrubber Tower
Made of fiberglass material, it has good resistance to chemicals such as acid, alkali, and salt, and can be used to handle various corrosive gases and liquids. It can effectively resist the erosion of chemicals and extend the service life of equipment.
FRP pipes
FRP pipe is a kind of computer-controlled mechanical winding from the production of products, is a light,high-strength,corrosion-resistant non-metallic pipe.It is made of resin as matrix and glass fiber as reinforcing material by special process. lt has the advantages of corrosion resistance,anti-leakage,heat insulation,light weight, high strength,long service life,strong designability,small fluid resistance,convenient installation and low cost,etc.
FRP water tanks
Glass Fiber Reinforced Plastic (FRP) water tank is a kind of water storage equipment made of composite materials.The tank is manufactured through high-temperature and high-pressure molding processes. It uses food-grade resins and fiberglass reinforcement, which guarantees water safety and hygiene standards.The product features a modular design with diversified standard panel specifications and optional thickness configurations.The water tank has the advantages of anti-aging, anti-leakage, easy to clean, and long service life.
PPH Agitator tank
The agitator of various types and materials has the same corrosion resistance as the tank.It is used for chemical reactions such as neutralization,oxidation, reduction, precipitation, flocculation, preparation, mixing and dilution of chemical media.lt can replace and make up the deficiency of stainless steel, glass lining, glass lining and fiberglass equipment.
Horizontal FRP Tanks
Glass fiber reinforced plastic（FRP） tank is a kind of glass fiber reinforced plastic products. It is a new type of composite material made by glass fiber and resin and wound by a microcomputer controlled machine. It is composed of corrosion resistant lining layer, seepage proof layer, fiber winding strengthening layer and outer protective layer with high resin content.
Square cooling towers
Glass fiber reinforced plastic (FRP) cooling towers are categorized into cross-flow, counter-flow, spray-type, and non-powered types, featuring rational structural designs with concrete supporting frameworks. These FRP cooling towers demonstrate excellent cooling efficiency, low noise levels, minimal water splashing, stable performance, easy maintenance, and large circulating water capacity, making them suitable for various industrial recirculating water systems.
FRP reaction tanks
FRP reaction tank,a wide range of advanced technology,stable quality,corrosion resistance,easy to operate and so on.Widely used in petroleum,chemical,food,medicine,pesticide.scientific research and other industries,is used to complete the polymerization, condensation,vulcanization,hydrocarbon,hydrogenation and other chemical processes of reaction equipment.
FRP Liquid Alkali Storage Tank
Good corrosion resistance: Fiberglass can withstand the corrosion of liquid alkali, prevent the tank from being corroded, extend service life, and reduce the risk of liquid alkali leakage caused by tank corrosion.
FRP Mixing Tank
The noise generated by the fiberglass mixing tank during operation is relatively small, because the fiberglass material itself has certain shock absorption and noise reduction performance.
Circular cooling towers
Glass fiber reinforced plastic (FRP) cooling towers are categorized into cross-flow, counter-flow, spray-type, and non-powered types, featuring rational structural designs with concrete supporting frameworks. These FRP cooling towers demonstrate excellent cooling efficiency, low noise levels, minimal water splashing, stable performance, easy maintenance, and large circulating water capacity, making them suitable for various industrial recirculating water systems.
